山東山汽工程機械(集團)有限公司
熱線電話:400-879-1999 山汽官方微信
鄭重聲明 購機 售后
在線詢價
熱線電話:400-879-1999
您現在所在的位置: 首頁> 新聞資訊 > 行業新聞 >

攪拌車的罐體故障如何維修?

所屬分類:行業新聞 發布時間:2020-07-13 來源:http://www.whjchh.com 瀏覽量:18

  全自動上料攪拌車用溶劑徹底清理閥桿和閥體。用壓縮空氣吹干所有零件,然后用ATF油作為潤滑劑,重新組裝。大家在選擇時我們會有專門的技術人員為大家解答,建議大家收工時,要徹底清洗混凝土貯罐及進出料口周圍,保證不粘有水泥及混凝土結塊。在閥桿表面涂ATF油,然后將其落入閥孔中。閥桿應能靠自重落入閥孔底部。否則,重復步驟,重新測試。如果閥桿仍然卡滯,則更換閥體。
  Clean the valve stem and valve body thoroughly with solvent. Dry all parts with compressed air and reassemble with ATF oil as lubricant. When you choose, we will have a special technical personnel to answer for you. It is suggested that when you finish work, you should thoroughly clean the concrete storage tank and the area around the inlet and outlet to ensure that there is no cement and concrete caking. Coat the surface of the valve stem with ATF oil and drop it into the valve hole. The valve stem should be able to fall into the bottom of the valve hole by its own weight. Otherwise, repeat step and retest. If the stem is still stuck, replace the valve body.
  全自動上料攪拌車的檢修在整個工程作業中也是極為重要的,做好基本的檢修我們的工作才能正常進行。首先將砂紙置于ATF油中,浸泡約30分鐘。小心地敲擊閥體,使卡滯的閥桿從閥腔孔中落下。可能有必要使用一把小螺絲刀,將其撬出。
          全自動上料攪拌車
  The maintenance of the automatic feeding mixer is also very important in the whole project operation. Only by doing a good job in the basic maintenance can our work be carried out normally. First place sandpaper in ATF oil and soak for about 30 minutes. Carefully tap the valve body to allow the stuck stem to fall out of the cavity bore. It may be necessary to lever it out using a small screwdriver.
  全自動上料攪拌車小心不要劃傷閥孔。單向閥桿是否有摩擦痕跡。使用ATF油浸泡過的#600砂紙,打磨閥桿上的毛刺,然后在溶劑中清洗閥桿并用壓縮空氣吹干。卷起半張ATF油浸泡過的#600砂紙,將其插入卡滯閥桿的閥孔中。輕輕扭動砂紙,使砂紙松卷,緊密貼合在閥孔表面,然后邊推拉,邊扭卷砂紙,打磨閥孔。抽出#600砂紙。在溶劑中徹底清洗整個閥體,然后用壓縮空氣吹干。
  Be careful not to scratch the valve hole on the automatic feeding mixer. Check whether there are friction marks on the one-way valve stem. Grind the burrs on the valve stem with ? 600 sandpaper soaked in ATF oil, then clean the valve stem in solvent and dry it with compressed air. Roll up half a piece of ? 600 sandpaper soaked in ATF oil and insert it into the valve hole with stuck valve stem. Gently twist the sandpaper to make the sandpaper loose and tightly fit on the surface of the valve hole. Then, while pushing and pulling, twist the sandpaper to polish the valve hole. Draw out 600 sandpaper. Clean the entire valve body thoroughly in solvent and blow dry with compressed air.
  以上是關于攪拌車罐體故障維修的措施,想要了解更多攪拌機內容歡迎點擊http://www.whjchh.com官網給我們留言。
  The above is about the mixer tank troubleshooting measures, want to learn more about mixer content, welcome to click http://www.whjchh.com Leave us a message on the official website.
熱門產品 / HOT PRODUCT

 

首頁 產品 電話 置頂
99视频在线精品国自产拍亚瑟|bt天堂在线 男人影视|秋霞A级毛片在线看理论片|亚洲日韩欧美在线无卡