山東山汽工程機械(集團)有限公司
熱線電話:400-879-1999 山汽官方微信
鄭重聲明 購機 售后
在線詢價
熱線電話:400-879-1999
您現在所在的位置: 首頁> 新聞資訊 > 行業新聞 >

全自動上料攪拌車傳動油質量檢測應該注意什么?

所屬分類:行業新聞 發布時間:2020-11-26 來源:http://www.whjchh.com 瀏覽量:18

在設備的實際操作期間,自上料攪拌車的轉移也是非常重要的組成部分。因此,我們需要在使用過程中測試機油的質量。那么我們如何具體運作?
During the actual operation of the equipment, the transfer from the loading mixer is also a very important part. Therefore, we need to test the quality of the oil in use. So how do we operate?
1.將自上料攪拌車停在水平表面上并擰緊手剎。
1. Park the self loading mixer on the horizontal surface and tighten the handbrake.
2.讓發動機怠速運轉幾分鐘。
2. Let the engine idle for a few minutes.
3.踩下制動踏板,將操縱桿轉至倒檔,前進檔等,并在每個檔上停留幾秒鐘,以向變矩器和所有換檔執行器注滿液壓油。后,將操縱桿轉到停車位置。
3. Step on the brake pedal, turn the control lever to reverse gear, forward gear, etc., and stay at each gear for several seconds to fill the torque converter and all shift actuators with hydraulic oil. After that, turn the lever to the park position.
4.從加油管上取下自動變速箱油尺,將清潔過的油尺插入加油管,然后將其拉出以檢查油尺上的油位。
4. Remove the automatic transmission dipstick from the oil filler tube, insert the cleaned dipstick into the filler tube, and then pull it out to check the oil level on the dipstick.
在檢查自上料攪拌車或對其進行故障排除之前,請先檢查變速箱油位和油質。將變速桿置于P位置,在空轉時運轉發動機至少幾分鐘,油液達到正常的工作溫度,并且車輛必須停放在水平表面上,以確保差速器和油門之間的油位。傳輸通常是穩定的。
全自動上料攪拌車
Please check the gearbox oil level and oil quality before checking or troubleshooting the self loading mixer. With the shift lever in position P, run the engine at idle for at least a few minutes, the fluid reaches normal operating temperature, and the vehicle must be parked on a horizontal surface to ensure the oil level between the differential and the throttle. Transmission is usually stable.
卸載自上料攪拌車時的注意事項
Precautions for unloading from loading mixer
自上料攪拌車在某些建筑過程中是常見的機械車輛設備,并且在操作設備的過程中有某些預防措施。因此,讓我們看一下當今卸料過程中自上料攪拌車的注意事項。
Self loading mixer is a common mechanical vehicle equipment in some construction process, and there are some preventive measures in the process of operating the equipment. Therefore, let's take a look at the matters needing attention of the self loading mixer in the unloading process.
1.卸貨前,讓混合罐全速運轉一到兩分鐘,使混凝土攪拌均勻。如有必要,加一些水使混凝土均勻混合并易于卸料。
1. Before unloading, let the mixing tank run at full speed for one to two minutes to make the concrete mix evenly. If necessary, add some water to make the concrete evenly mixed and easy to unload.
2.清除物料后,將汽車盡可能停放在地面上,然后弄濕料斗斜槽以方便清潔。
2. After removing materials, park the car on the ground as much as possible, and then wet the hopper chute to facilitate cleaning.
3.好在安裝時看一下物料,以免操作卸料桿。倒退中間位置時好停止燃油箱,以保護減速器,支撐輪等。
3. It is good to check the materials during installation to avoid operating the unloading rod. When reversing the middle position, stop the fuel tank to protect the reducer, support wheel, etc.
4.洗瓶時必須仔細清洗,并將水反復倒轉兩次,然后松開,后一次將水倒入水箱中放入水箱中,然后返回工位并加水徹底清洗水箱。
4. The bottle must be cleaned carefully, and the water should be turned back twice repeatedly, and then released. After that, the water will be poured into the water tank and put into the water tank. Then, return to the working position and add water to clean the water tank thoroughly.
為了確保自上料攪拌車運行期間設備的良好運行性能,我們希望您必須了解這些注意事項。由于對設備的了解不足,因此在操作過程中避免了操作錯誤,這會影響正常施工過程的進度。
In order to ensure the good operation performance of the equipment during the operation of the charging mixer, we hope you must understand these precautions. Due to the lack of understanding of the equipment, operation errors are avoided in the operation process, which will affect the progress of normal construction process.
熱門產品 / HOT PRODUCT

 

首頁 產品 電話 置頂
99视频在线精品国自产拍亚瑟|bt天堂在线 男人影视|秋霞A级毛片在线看理论片|亚洲日韩欧美在线无卡